Bmw M3 E36 3.2 Turbo 600Hp - 4SALE -

maleckis · Post by **maleckis** » 07 Nov 2007, 21:24

Hehe. Thanks a lot for updates. It is enjoyable to read about turbo-charging of euro s50b30 in understandable language

. In Poland my M3T is 2nd and the latest one, so there aren't a lot of people who have experience with that engine.

I see you have one guy who does everything

. Thanks to that you take pics only... and say Swedish jokes

. Tiring job...

Seriously, are you going to remain an air conditioning? Before we started turbocharging we had removed all needless parts such as an air conditioning, a carrier, an air pump, a carbon filter housing, a few hoses and sensors etc.

Free room after removing the carrier:

shellack the holy M tomorrow!

Vision79 · Post by **Vision79** » 07 Nov 2007, 22:43

maleckis wrote:Hehe. Thanks a lot for updates. It is enjoyable to read about turbo-charging of euro s50b30 in understandable language . In Poland my M3T is 2nd and the latest one, so there aren't a lot of people who have experience with that engine.

I see you have one guy who does everything . Thanks to that you take pics only... and say Swedish jokes . Tiring job...

Seriously, are you going to remain an air conditioning? Before we started turbocharging we had removed all needless parts such as an air conditioning, a carrier, an air pump, a carbon filter housing, a few hoses and sensors etc.

Free room after removing the carrier:

shellack the holy M tomorrow!

hehe, between the photos iam doing some as well

The goal is to maintain all things like servo,ac,airpump and so on...its still a car that should run 1000km on highway without any serious problems bcs of turbo installation..but if we need to do some changes we will face that problem that day.

We want to build the car so original looking and discret so the "swedish authority" wont see any special when lifting the hood.

Even if we change turbo and hits the 700hp barier...i belive as daily driver it will run tops 550-600hp to save the internals for funny events

Vision79 · Post by **Vision79** » 09 Nov 2007, 17:35

Friday´s work is just drinking some beer..watch IDOL yeah i know..im like a girl..but a girl with cold beer

Tomorrow is D-day...today Patrik pulled the goldcard to buy a enginehoist and a tilter for tomorrows work with the M3.

Not much more than this for today!

oh i almost forgott

, The Wiseco pistons and Spm rods were send out today from PPF so prolly have it on mon-tues, greeeeeat!!!

Tjottirotti · Post by **Tjottirotti** » 09 Nov 2007, 19:08

Här har vi den omtalade m3an... blir nog ascoolt när den blir klar

lär ju flytta på sig

Vision79 · Post by **Vision79** » 09 Nov 2007, 19:57

Tjottirotti wrote:Här har vi den omtalade m3an... blir nog ascoolt när den blir klar lär ju flytta på sig

Ja det blir en rolig smiska gata maskin

, türk amazon som kommer aktersegla det mesta i sportbilsväg.

Men vi gillar att jaga hojjar så vi fortsätter nog med det tror ja

Vision79 · Post by **Vision79** » 10 Nov 2007, 11:23

BIG BANG!

Idag ska Mr M lämna kroppen och hamna på operationsbordet!

( Chris, today the engine is leaving the car...time for operation

)

Vision79 · Post by **Vision79** » 10 Nov 2007, 19:08

Done Deal!

The engine has left the building....or was it elvis? haha...funny me

Not so much to tell..see the pictures and enjoy!

Then MagnusB (also a builder of a very serious and good looking M3 Turbo) droped byt with he´s custom made engine mount...looks great, nice job!!

We also got some special equipment to deal with the vanos unit.

Thats about it today....tearing the engine apart is prob Patrik´s evening jobs or if we do a forced job togheter this week coming!!

until then....

Dont forget!....always...always..WIDE OPEN THROTTLE!

P E A C E !!!!!

Vision79 · Post by **Vision79** » 11 Nov 2007, 21:33

Kul med alla kommentarer

Den här updaten blir på svenska ( sorry chris..only swedish today

)

Idag har det mesta tagits isär gällande motorn...inte mkt o säga...kolla själv.

"M-Porr"

That was for today....

efter detta så var d raka spåret ca 8-10km längre bort till MagnusB som oxå har ngt skoj i garaget...* spy pics *

En röd...en blå......2008 = ett bra år för Sundsvalls däckaffärer

P.s Idag såldes GT3082R snurran till förmån för ett likadant som hör ihop med den röda räsern ovan

...GT35R..antagligen ngt som köps via PPF

AndreasT · Post by **AndreasT** » 11 Nov 2007, 22:02

S50b32 är sjukt fin motor!
Med tanke på turbovalet i denna maskin kommer den bli grymt körbar.

moonzhine · Post by **moonzhine** » 11 Nov 2007, 22:04

hehe den röda verkar intressant..ovanlig färg iaf..

Vision79 · Post by **Vision79** » 11 Nov 2007, 23:01

AndreasT wrote:S50b32 är sjukt fin motor!
Med tanke på turbovalet i denna maskin kommer den bli grymt körbar.

Tjena

Ja det är ju det som är tanken...försöka hitta en sån linjär kurva som möjligt fast med gott mos till varvstoppet

Vision79 · Post by **Vision79** » 11 Nov 2007, 23:04

moonzhine wrote:hehe den röda verkar intressant..ovanlig färg iaf..

Ja den röda blir mkt trevlig..mkt fint handlag och grymt tänkande ligger bakom den...blir hög finish på den turbo installationen kan ja lova!.

maleckis · Post by **maleckis** » 12 Nov 2007, 19:34

You’re pretty fast. Removing a cylinder head in my s50b30 lasted almost 2 weeks, but engine was still in a car.

I see your NA pistons are in worse condition than mines stock after blown head gasket. Piece of piston came off… that m3 had tough life with you

. When I took out the cylinder head I was able to see inscription “S50B30, 10.8”

.

Are you going to replace bearing shells?

What are specs of that red m3 whom you posted pics of? What’s the engine: B30 or B32? I see Vanos is removed. In what position did they put camshafts without vanos unit? Are they stock camshafts? Could you say more, Jonas? It might be via PM.

Regards,
Chris.

Vision79 · Post by **Vision79** » 12 Nov 2007, 22:57

maleckis wrote:You’re pretty fast. Removing a cylinder head in my s50b30 lasted almost 2 weeks, but engine was still in a car.

I see your NA pistons are in worse condition than mines stock after blown head gasket. Piece of piston came off… that m3 had tough life with you . When I took out the cylinder head I was able to see inscription “S50B30, 10.8” .

Are you going to replace bearing shells?

What are specs of that red m3 whom you posted pics of? What’s the engine: B30 or B32? I see Vanos is removed. In what position did they put camshafts without vanos unit? Are they stock camshafts? Could you say more, Jonas? It might be via PM.

Regards,
Chris.

The pistons had alot of "carbon" rest´s..but the rest were very fine and precise...the engine/car has about 90 000km.

I could guess u would be interested in the red one

hehe...its a B30

All bearings and gaskets will be replaced, we are sending the engine block to the engine tuner for matchbore to

I belive they are stock camshafts but i cant confirm it right now...i know MagnusB the owner is here from time to time at the forum so maby he can tell you him self

maleckis · Post by **maleckis** » 13 Nov 2007, 14:41

Did you order over sized pistons? Could you find out for me what length of SPM forged rods you bought is? What compression ratio are you going to have? 8.8:1?

Please, suggest him looking here and saying more about specs of his M3

.

Vision79 · Post by **Vision79** » 13 Nov 2007, 20:25

maleckis wrote:Did you order over sized pistons? Could you find out for me what length of SPM forged rods you bought is? What compression ratio are you going to have? 8.8:1?

Please, suggest him looking here and saying more about specs of his M3 .

Sure i will talk to Magnus and "fish" some info

the pistons are 8.8.1 , but if u have the B30 crank its diffrent with the rods anyway i belive ?! , Pistons are slightly overbored about 1/10 and regarding lenght of rods they are 139mm.

Here are some pictures of a swedish dildo!!

(or maby just something that came in a package from AVESTA

The Crank...

The SPA turbo manifold

Matchported to the M3 exhaustports..

Last job..then carying out in the trunk of the car to be left at the local engine tuner tomorrow.

If everything works out good, we could have the engine and cylinderhead back by friday

, so Patrik have to visit the local BMW shop and order some gaskets and bearings.

Rock n Roll!

From Russia with love!!...ok..Sweden.. it snows like hell anyway

Fido85 · Post by **Fido85** » 13 Nov 2007, 20:52

fan vad ni har mycket snö

här har vi ingenting